Endings T1: Base Ending

Durawatt compressed cartridge heaters. base Ending Ref. "T1"
The cartridge is fully compressed, with a heat-resistant ceramic paste which seals the entry. The remaining cartridges are made from this base.

Endings T2: Soap stone Ending

Durawatt compressed cartridge heaters. Soap stone Ending Ref. "T2"
Cartridge with one steatite ceramic piece which juts out. It is 3mm to 6mm long, depending on the diameter of the cartridge. It prevents the connexion of the wire with the tube, thereby giving more consistency to the cable entry.

Endings T3: Chip Ending

Durawatt compressed cartridge heaters. chip Ending Ref. "T3"
Cartridge with a steatite ceramic piece. Ready for a quick change of wires.

Endings T4: Metric Ending

Durawatt compressed cartridge heaters. metric Ending Ref. "T4"
Cartridge with stainless steel metric stud. Useful for quick change of wires.

Endings T5: Unipolar Ending

Durawatt compressed cartridge heaters. unipolar Ending Ref. "T5"
Cartridge with an unipolar fiberglass cable for low voltage cartridges

Endings T6: Unipolar Screw Ending

Durawatt compressed cartridge heaters. unipolar screw Ref. "T6"
Cartridge with a metric unipolar screw output for a quick cable extraction.

Endings T7: Iron Plate Ending

durawatt compressed cartridge heaters. (pletina) iron plate Ending Ref. "T7"

Fully compressed and reinforced cartridge. Ready for fastening the object to be heated. Ideal for areas with motion and vibration.

Diameter mm. & Inches	6,5-1/4"	8-5/16"	10-3/8"	12,5-1/2"	16-5/8"	20-3/4"	25-1"
A mm	18	18	27	27	33	33	41
B mm	13	13	20	20	25,6	25,6	33
C mm	3,2	3,2	3,2	3,2	4,2	4,2	5,2
D mm	1 to 1,2	1 to 1,2	1 to 1,2	1 to 1,5	1 to 1,5	1 to 2	1 to 2

Endings T7B: Iron Plate Ending

Durawatt compressed cartridge heaters. (pletina) iron plate Ending Ref. "T7B"
Fully compressed and reinforced cartridge. Ready for fastening the object to be heated. Ideal for areas with movement and vibration.

Diameter mm. & Inches	6,5-1/4"	8-5/16"	10-3/8"	12,5-1/2"	16-5/8"	20-3/4"
A mm	6 ,5	8	9,5	10	12	18
B mm	6,5	8,5	9,5	11,25	13,5	16,5
C mm	6,5	9	9	10	11	13
D mm	3,2	4,2	4,2	5,2	5,2	6,2
E mm	2,25	2	2	1,5	2	2

Endings T8: Nipple Ending

Durawatt compressed cartridge heaters. nipple Ending Ref. "T8"
Full water resistant and reinforced cartridge. Ready for removals by means of a screw if the cartridge becomes dislodged. Ideal for areas where pressure and fluids are watertight. The finish Ref.T8 is indicated for heating for areas with internal pressure (oil tanks, water, glues, plastics) or deflagration.

Diameter mm. & Inches	6,5-1/4"	8-5/16"	10-3/8"	12,5-1/2"	16-5/8"	20-3/4"
A mm	10	10	12	12	14	14
B mm	4	4	4	4	4	4
C mm	12	14	17	19	24	27
Screw mm. & Inches	M10 (1/8'')	M12 (1/4'')	M14 (1/4'')	M16 (3/8'')	M20 (1/2'')	M26 (3/4'')

Quotes subject to variation without prior notice.

Endings T9: Ending 90º

Durawatt compressed cartridge heaters. Ending 90º Ref. "T9"
Full water resistant and reinforced cartridge. Ready for removal from its accommodation. With reinforcement which prevents deformation in case of displacement of the same. The finish T9 can be used in any hostile situation (high temperatures, waste material).

ø Cartridge	6,5	8	10	12,5	16	20	25
ø Tube	6,5	8	10	12,5	14	18	20
A	8	10	12	15	18	25	30

Cartridge heaters outputs 90º base. Ref: T9 Base.		Cartridge heaters outputs 90º protection base. Ref: T9 PB.
D 6,5 8 10 12,5 16 20 L 10 11 12 13 16 18		D 6,5 8 10 12,5 16 20 L 10 11 12 13 16 18

Special cartridge heaters. smelting of non-ferrus metals. Ref: T9 Stock.
Stock of Maxiwatt high density cartridges, especially for smelting of non-ferrous metals.

Diameter Long. mm Watts 10 80 250 12,5 60 200 80 250 90 350 16 80 315 100 500 160 630 180 800 200 800 250 1000 20 100 630 160 800

Cartridge heaters outlets elbow. Ref: T9 Elbow.

A

6,5

8

10

12,5

16

20